They are making a few great points regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this article which follows.
Mounting a tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is conveniently obtainable, the task can relocate rapidly; if you have to open up a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task and fit trying it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one prior to you start. Chances are you might require a specialist plumber to make tube links.
This article will certainly assist you set up a new bathtub in your washroom if you have currently gotten a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washing machines remain in place between the faucet and also the sink. Secure the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at the very least once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to problems with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about How to Install a Bathtub, I thought sharing that excerpt was really helpful. Kindly take the time to share this content if you liked it. Thank-you for going through it.
Schedule A Service Call